Terrestrial laser scanning (TLS) has been used extensively in Earth Science for acquisition of digital outcrop data over the past decade. Structure-from-motion (SfM) photogrammetry has recently emerged as an alternative and competing technology. The real-world performance of these technologies for ground-based digital outcrop acquisition is assessed using outcrops from North East England and the United Arab Emirates. Both TLS and SfM are viable methods, although no single technology is universally best suited to all situations. There are a range of practical considerations and operating conditions where each method has clear advantages. In comparison to TLS, SfM benefits from being lighter, more compact, cheaper, more easily replaced and repaired, with lower power requirements. TLS in comparison to SfM provides intrinsically validated data and more robust data acquisition in a wide range of operating conditions. Data post-processing is also swifter. The SfM data sets were found to contain systematic inaccuracies when compared to their TLS counterparts. These inaccuracies are related to the triangulation approach of the SfM, which is distinct from the time-of-flight principle employed by TLS. An elaborate approach is required for SfM to produce comparable results to TLS under most circumstances.
Digital outcrop acquisition is the process of obtaining a digital representation of an outcrop with sufficient detail, precision, and accuracy such that it forms a usable duplication of its real-world counterpart, most commonly presented as a three-dimensional model (Xu et al., 2000; Pringle et al., 2001; Jones et al., 2004, 2009; Bellian et al., 2005; Clegg et al., 2005; Hodgetts et al., 2004). Digital outcrop models provide a means to gain quantitative data (e.g., Ahlgren et al., 2002; McCaffrey et al., 2005; Trinks et al., 2005; Jones et al., 2008a; Enge et al., 2010) over a range of scales, forming a key input in reservoir geomodeling workflows (Pringle et al., 2004, 2006; Thurmond et al., 2006; Labourdette and Jones, 2007; Howell et al., 2014).
No single technology is universally best suited to all digital outcrop acquisition. Successful acquisition relies on three interrelated factors: (1) An understanding of the range of acquisition methods available, and their application; (2) selection of one or more suitable methods for a chosen outcrop; and (3) the required geological measurements and interpretations to be made from the digital representation. In many cases, there are limitations in the available acquisition methods and/or suitable outcrops at which to apply these successfully, thus forcing compromise of the all-important measurements and interpretations. Skill with multiple acquisition methods and an appreciation of their strengths and weaknesses are therefore vital to acquire suitable data for any given outcrop and purpose.
A range of different digital outcrop acquisition methods exist; these methods can be split into airborne- and ground-based approaches. Airborne methods and applications include the use of airborne laser scanning from conventional aircraft; for example, as used to analyze faulting in Slovenia (Cunningham et al., 2006) and the San Andreas fault (Bevis et al., 2005; Arrowsmith and Zielke, 2009; Hilley et al., 2010) and to model paleokarst layers in the Billefjorden region of Svalbard (Buckley et al., 2008a); unmanned aerial vehicle (UAV)–mounted laser scanning (Lin et al., 2011) and structure-from-motion (SfM) photogrammetry, as used to map coastal erosion (Mancini et al., 2013); SfM photogrammetry from manned aircraft, as used to monitor active lava dome topography (James and Varley, 2012); and kite-mounted SfM photogrammetry, as used, for example, to construct multispectral terrain models of intertidal landscapes at Greenfields beach, New South Wales (Bryson et al., 2013).
Ground-based methods of outcrop acquisition are used in a very wide range of diverse applications. Examples include: (1) terrestrial laser scanning (TLS), used to characterize fracture systems (Ahlgren et al., 2002), to map Miocene deep-water slope-channel architecture in Victorio Canyon, West Texas (Bellian et al., 2005), to analyze fluvial channel architectures near Ainsa, Spain (Labourdette and Jones, 2007), and to describe dolomite bodies, in three dimensions, within the Latemar platform carbonates, in northern Italy (Jacquemyn et al., 2015); (2) standard stereo-pair photogrammetry, used to analyze Carboniferous marine sequences (Pringle et al., 2004); (3) SfM photogrammetry, used to measure structural features in folded Upper Cretaceous marl and limestone, in southwest Vienna (Schober and Exner, 2011); (4) real-time kinematic global positioning systems (GPS), used to quantify fold geometries in Carboniferous limestones in NE England (Pearce et al., 2006); (5) combined GPS and laser range finding, used to map synsedimentary growth faults at Muddy Creek, Wyoming (Xu et al., 2000); and (6) time-of-flight camera range imaging that was used to analyze speleothem features at short range in Dechen Cave near Dortmund, Germany (Hammerle et al., 2014).
Hybrid approaches combining air- and ground-based methods have also been implemented (e.g., Pringle et al., 2004; Jones et al., 2009; Buckley et al., 2010; Bemis et al., 2014; Jacquemyn et al., 2015). Overhanging and vertically orientated outcrop can be problematic to acquire from an aerial perspective. Combining ground and aerial methods helps to address this issue. Methods to extend virtual outcrop models into the shallow subsurface are summarized in Pringle et al. (2006) and Jones et al. (2011).
Of all the ground-based methods, TLS and SfM provide the most comprehensive and versatile outcrop representations, at scales where measurements were traditionally taken directly by hand at the outcrop. Most published studies are based on either TLS or SfM, although both methods can be combined as hybrid data sets in order to maximize spatial coverage and point density, for instance during topographic mapping of the Fogo volcano following the 2014–2015 eruption (Richter et al., 2016).
The aim of this study is to provide a robust comparative analysis of the real-world performance of these two methods using corresponding data acquired at outcrops in North East England and the United Arab Emirates. SfM is often presented as a simpler and cheaper alternative to TLS; however, comparison of the two methods shows strengths and weaknesses in both and reveals subtle but significant differences in their output. Our comparison provides an indication of the elaborate approach required for the successful implementation of SfM. The advantages and limitations of the two methods from our experience will also be discussed, including important practical considerations for field-based geoscientists.
2. ACQUISITION METHOD OVERVIEW
2.1. Terrestrial Laser Scanning
Over the past decade, TLS has been used extensively in Earth Science as a tool for acquisition of three-dimensional (3D) outcrop surface data sets (Jones et al., 2008b). The technology, its performance, and its application for common acquisition tasks and analyses within Earth Science are well established (Slob and Hack, 2004; Buckley et al., 2008b; Heritage and Large, 2009). Laser emissions are confined to the near-infrared to ultraviolet spectrum. These electromagnetic waves do not travel through solid objects; thus, to acquire data, the laser scanner must have a direct unobstructed line of sight to the outcrop of interest. Many outcrops are geometrically complex and cannot usually be seen in their entirety from a single vantage point. This self-obstruction leads to shadow regions within the laser scan data, which are minimized by placing the laser scanner in a number of vantage points (often termed scan positions) about the outcrop. Point clouds generated from different scan positions are typically co-located using reflective targets, which act as common reference points to align multiple point clouds within a common coordinate system. The process of aligning multiple scan positions to a georeferenced reflector array also provides an independent validation of the accuracy of the laser scanner. The real-world positions of reflectors are commonly measured using the Global Navigation Satellite System (GNSS). The areas of the scanned outcrops are sufficiently small for the curvature of the Earth to be ignored. Comparison of the scan-based and real-world reflector positions are then used to generate a transformation matrix describing the rotation and translation required to align the reflectors and scan data to real-world positions (Supplemental Items: Supplemental Table 11). Scaling is unaltered in this process and is calculated independently at the time of acquisition using calibration parameters relating the laser wave velocity in air of known temperature, pressure, and humidity.
The flexibility of this TLS technology provides a potentially vast range of applications beyond outcrop acquisition and feature mapping. Applications include temporal change detection (Alba and Scaioni, 2010; Wilkinson et al., 2010, 2012; Abellán et al., 2011; Lim et al., 2011; DeLong et al., 2014) and the integration with other acquisition techniques such as multispectral imagery (Buckley et al., 2013) and ground-penetrating radar (Jones et al., 2011; Bubeck et al., 2015).
2.2. Structure-from-Motion Photogrammetry
Structure-from-motion (SfM) photogrammetry involves the three-dimensional reconstruction of a scene from a suite of two-dimensional images (Ullman, 1979). The structure-from-motion photogrammetry acquisition and subsequent image-processing workflow have been previously described in numerous different implementations and adaptations (e.g., James and Robson, 2012, 2014; Westoby et al., 2012; Bemis et al., 2014). Acquisition involves the collection of a suite of overlapping digital images of the outcrop from multiple perspectives. Each piece of outcrop must be seen in at least two images in order for the processing workflow to successfully reconstruct its three-dimensional geometry; although, in practice, the outcrop is imaged to a greater degree in order to provide additional redundancy. Differing perspectives between multiple images sampling the same piece of outcrop are maximized, while maintaining significant similarity between images in order to constrain the geometric reconstruction from multiple orientations. The concept of achievable precision is explored in detail by James and Robson (2012), who identify a number of parameters that affect reconstruction. Parameters include the strength of the photogrammetric network, the mean distance from camera to the outcrop, the number of overlapping images, and parameters relating to the intrinsic and extrinsic properties of the camera body and lens in use, such as sensor size and parameters describing focal length and lens distortion. Acquiring multiple images of each piece of the outcrop from sufficiently different ground-based perspectives presents a challenge, even when several vantage points exist. Multi-rotor unmanned aerial vehicles (UAVs) provide a solution through their ability to hover and image the outcrop from a greater range of perspectives (e.g., Bemis et al., 2014). Following image acquisition, the three-dimensional digital outcrop model is produced by processing the images on a workstation using a photogrammetric workflow (e.g., Fig. 1). Success of the SfM approach relies on the ability of the workflow to detect and match correspondingly distinct outcrop features (often termed key points) between images. The scale-invariant feature transform (SIFT) (Lowe, 2004) is a common implementation of feature detection and matching. Each key point identified in multiple images is included in the final outcrop model as a discrete point in 3D space, providing it passes a set of quality-assessment criteria (commonly a minimum and maximum perspective change between the seed images and its position conformance with surrounding key points). A camera calibration model (e.g., Brown, 1966) describing the radial, tangential, and decentering distortion of the image due to lens and camera body is used to remove these effects by undistorting the images prior to key-point detection and matching (Fig. 1, step A). If the camera calibration is unknown, an estimate can be calculated during the matching process, although the final accuracy of the outcrop model will be compromised. Key point detection and matching are then applied to the image suite (Fig. 1, steps B and C). The distribution of matches between images and how this array changes between images are used to calculate the relative position and orientation of each image in 3D space (Fig. 1, step D). Once the camera positions and orientations are known, the matches can be projected to form a sparse point-cloud outcrop model (Fig. 1, step E), and the result can be visualized. Images with poor similarity to others in the suite do not contain enough valid matches to calculate their position and orientation within the model and thus are excluded from the rest of the workflow. Excluded images can disrupt outcrop reconstruction, particularly if image acquisition was conducted in a simple chain-like manner where little overlap exists in the images beyond their immediate neighbors. To increase outcrop model point density, the workflow interrogates the images used in the sparse model with increased aggressiveness in the search for further key-point matches (Fig. 1, step F). This is computationally intensive, but the comparison of images is limited to those that are known to overlap by using the image positions and orientations calculated during the generation of the sparse model. The dense outcrop model is presented in its own photogrammetric coordinate system, which lacks real-world scale, orientation, and position. Reference data are used to scale, orientate, and position the outcrop model into a real-world coordinate system (Supplemental Items: Supplemental Table 2 [see footnote 1]). Reference data exist in a range of precisions and accuracies that provide solutions of varying quality. Such data include outcrop control points surveyed using GNSS, vertically orientated surveyor’s poles of known length, as well as the position and orientation of the camera measured at the time of image acquisition (for an evaluation of referencing methods, see Sturzenegger and Stead, 2009). A transformation matrix is calculated by comparing the reference data with their counterpart representation in the photogrammetric coordinate system. The matrix is used to transform the dense outcrop model from photogrammetric to real-world coordinate systems. The transformation forms the final stage of the SfM workflow (Fig. 1, step G), after which the outcrop model is ready for further task-specific processing and interpretation.
3. OUTCROP DATASETS
Two outcrops representing typical study sites were chosen for a real-world comparison of the two acquisition methods: a Carboniferous limestone quarry outcrop in North East England and a fractured Cretaceous limestone outcrop near Ras al-Khaimah, United Arab Emirates. Both outcrops were selected for their geological interest, specifically the three-dimensional exposure of fracture surfaces, rather than their particular suitability to either method. The data were acquired and processed using a range of field equipment and software, in the manner described in Section 2. An overview of the acquisition parameters and summary output for each method at both study sites is given in Table 1.
3.1. Limestone Quarry, North East England
A disused quarry near Stanhope in North East England (54.710°, –002.024°) was selected as the first site for this comparative study (Figs. 2A and 2B). The quarry exposes a 10-m-high, north-facing vertical wall of fractured Carboniferous limestone along a 260 m east-west cut. The outcrop is similar in extent and access to a classical road-cut exposure. Material has been extracted from the quarry through exploitation of the bedding-perpendicular natural fracture network, by prying naturally formed blocks from the face. The outcrop surface is therefore complex and angular, formed from a series of semi-planar faces representing fracture surfaces. A 20-m-wide quarry floor exists at the base of the outcrop, beyond which the surrounding hillsides to the north and northeast provide natural vantage points from which to observe the outcrop.
3.1.1. Terrestrial Laser Scan Data Set
The TLS data set was acquired over a four-hour period in overcast conditions. A Leica ScanStation C10 TLS (Fig. 3A) was used to acquire data at ranges of between 20 and 50 m from four scan positions (Fig. 2B), which provided near-complete data capture with minimal shadow. The Leica ScanStation C10 uses a visible green laser to acquire measurements with 6 mm accuracy (1σ) in standard conditions up to 50 m range (Leica Geosystems, 2011), of which the 0–50 m range encompasses the majority of the data acquired in this survey. Images acquired with a 4 megapixel digital camera internal to the scanner were used to color the point data to provide a visually accurate representation of the outcrop; their use is aesthetic only and does not influence the geometry of the resultant model. The vertical axis of each scan data set was constrained using the scanner’s dual-axis compensator with 1.5 arcsecond accuracy. Constraining the vertical axis simplifies the remaining alignment to rotations about this axis and translations within a Cartesian coordinate system. Three retroreflective targets (Figs. 2B and 3B) surrounding the outcrop were used to align the four scan positions into a single model. The targets were surveyed using GNSS. The GNSS data were post-processed relative to a local base station to provide reflector positions with centimeter accuracy. These GNSS-derived positions were used to transform the scan model into a real-world coordinate system (Supplemental Table 1 [see footnote 1]). Following transformation, the outcrop model was cropped to remove points outside of the exposed area of interest, such as the surrounding hillsides, vegetation, and the quarry floor. The resultant final outcrop model (Fig. 3C) contains 1.79 million points, with an average density of 1710 points per m2 and an average point spacing of 0.02 m.
3.1.2. Structure-from-Motion Photogrammetric Data Set
The SfM data set was acquired over a two-hour period in overcast conditions. The requirement to produce a model with point spacing comparable to the TLS data set was considered during selection of camera equipment and appropriate distance to the outcrop. A 12 megapixel Nikon D300 with Nikon AF-S DX Nikkor 10–24 mm f/3.5–4.5G ED and Nikon AF-S DX Nikkor 55–200 mm f/4.5–5.6G IF-ED VR lenses were used to acquire 200 images from 11 different vantage points (Fig. 4A). The focal lengths of the zoom lenses were taped fixed at 24 mm and 125 mm, respectively. Three of the vantage points were located within 10–30 m of the outcrop from which the 24 mm lens was used. The remaining eight vantage points were located within 200–250 m of the outcrop, and images were acquired using the 125 mm lens. The images from the 11 vantage points covered the extent of the outcrop with sufficient overlap and similarity to enable SfM reconstruction. Of the 200 images, 44 were acquired from four tripod positions, representing four of the 11 vantage points (Figs. 2B and 4B). A Trimble 5800 GPS receiver was set up as a local base station to record pseudorange and position data at one-second intervals for the entirety of the survey. A Spectra Precision ProMark 120 GNSS receiver occupied each tripod position for 30 min and recorded GNSS data at one-second intervals. Baselines between the base station and each tripod position were post-processed using Trimble Geomatics Office software to provide tripod positions with centimeter accuracy relative to the base station. The SfM processing workflow described in Section 2.2 was implemented using the visualSFM software package version 0.5.26 (Wu, 2007; Wu et al., 2011, 2013) to create the outcrop model. A PC workstation with dual Xeon E5-2620 processors and 128 GB RAM was used for this purpose due to its multithreading capability of 24 threads at 2.0 Ghz. The 24 mm and 125 mm lenses were calibrated using Agisoft Lens software version 0.4.1 to provide radial, tangential, and decentering distortion coefficients. The images were undistorted using this calibration prior to use in the SfM workflow (e.g., Fig. 4C). Key-point detection and matching aligned all 200 photos into a single photogrammetric model, providing a sparse point cloud and the orientations and relative positions of the cameras (Fig. 4B). A dense point cloud was subsequently computed by allowing the SfM software to produce the most detailed data set possible. The resultant data set contains 0.96 million points, with an average density of 880 points per m2 and an average point spacing of 0.03 m. The outcrop model was converted into a real-world reference frame by calculating the transformation matrix between the four tripod positions within the photogrammetric reference frame and their GNSS-derived positions in real-world coordinates (Fig. 4D). A summary of this transformation is shown in Supplemental Items: Supplemental Table 2 [see footnote 1].
3.2. Ras al-Khaimah, United Arab Emirates
Data for the second comparative study were acquired from a wadi outcrop (25.947°, 056.072°) near Ras al-Khaimah, United Arab Emirates (Figs. 5A and 5B). The east-west–trending outcrop extends 250 m up the wadi and exposes a 45-m-high, south-facing terraced slope, composed of well-bedded and well-fractured Cretaceous limestone (Wasia Group). The outcrop is located in the footwall of a high-angle reverse fault that dips toward the east, displacing the older Thamama Group in the hanging wall. Weathering of bed-bound, bedding-perpendicular fractures has resulted in rounded, undulating fracture surfaces. The 40-m-wide wadi is accessed by track to the west and is limited in extent to the east by tailings from a nearby quarry.
3.2.1. Terrestrial Laser Scan Data Set
The TLS data set was acquired over a two-and-a-half hour period in sunny conditions. A Riegl LMS-Z420i TLS (Fig. 6A) was used to acquire data at ranges of between 100 and 200 m from two scan positions. A Nikon D300 digital camera with 14 mm lens was mounted on the scanner and used to acquire imagery to color the point-cloud data. The Rigel LMS-Z420i uses a near-infrared laser to acquire measurements with 8 mm precision (1σ at 50 m) between ranges of 2–1000 m (Riegl Laser Measurement Systems, 2010). Four cylindrical reflectors (e.g., Fig. 6B) provided common marker points between the two scan positions, which allowed them to be aligned within a single internal coordinate system. The real-world positions of the cylindrical reflectors were surveyed using GNSS in a base-rover configuration, with the raw data post-processed to provide centimeter accuracy. A transformation matrix was calculated by comparing the reflector positions in the internal coordinate system with their real-world GNSS-derived coordinates (Supplemental Items: Supplemental Table 1 [see footnote 1]) and then applied to the TLS data set to rotate and translate it into real-world coordinates. The outcrop model was then cropped to remove points outside of the region of interest. The final model (Fig. 6C) contains 1.40 million points, with an average density of 206 points per m2 and an average point spacing of 0.07 m.
3.2.2. Structure-from-Motion Photogrammetric Data Set
The SfM data set was acquired over a two-and-a-half hour period in sunny conditions. The outcrop faced south and was well lit by the sun from behind the camera. The requirement to produce a model with point spacing comparable to that of the TLS data set was considered during selection of camera equipment and appropriate distance to the outcrop. An 18 megapixel Canon 650D with Canon EF 24–105 mm f/4.0 L IS USM lens with the focal length taped fixed to 24 mm (Fig. 7A) was used to acquire 337 images at a distance to the outcrop of ∼60 m. Of these images, 73 were positioned across five tripod positions placed at various vantage points in front of the outcrop (Figs. 5B and 7B). The remaining images were taken freehand and acted as fill-in between the tripod positions, such that the image suite covered the outcrop extent with sufficient similarity between multiple images. The tripod positions were surveyed using GNSS relative to a local base station in the manner described in Section 3.1.2. The 24 mm lens was calibrated using Agisoft Lens software version 0.4.1 to provide radial, tangential, and decentering distortion coefficients. The images were subsequently undistorted using this lens model (Fig. 7C) and loaded into the visualSFM software package version 0.5.26 (Wu, 2007, 2013; Wu et al., 2011) to create the outcrop model. A PC workstation with dual Xeon E5-2620 processors and 128 GB RAM was used for this purpose. Key-point detection and matching aligned all 337 images into one photogrammetric model, providing a sparse point cloud, and identifying the orientation and relative position of the cameras (Fig. 7B). A dense point cloud was subsequently computed by allowing the SfM software to produce the most detailed data set possible. This data set contains 3.36 million points, with an average density of 503 points per m2 and an average point spacing of 0.04 m. The outcrop model was scaled, rotated, and translated into its real-world position through calculation of a transformation matrix describing the alignment of the five tripod positions from the photogrammetric reference frame to the GNSS-derived real-world coordinates (Fig. 7D). A summary of this transformation is shown in Supplemental Table 2 (Supplemental Items, see footnote 1).
Comparing and assessing point-cloud data sets can be a detailed task because these data are geometrically complex and are often subtly different, due to the way in which different methods sample the outcrop with heterogeneous point spacing and density (e.g., Khoshelham, 2011). A residual point-to-point–based comparison using the CloudCompare software version 2.7.0 (EDF R&D, 2015) is presented here, whereby two point clouds (a reference point cloud and a comparison point cloud) are compared by calculating the distance between every point in the comparison point cloud to the nearest point in the reference point cloud. In order to visualize the difference between the two data sets, each point within the comparison cloud is colored to represent its distance to the nearest reference point (e.g., Figs. 8 and 9). For the point-to-point approach to be effective, the process relies on the residuals between the two point clouds to be of a similar magnitude to their point spacing; the two point clouds must be properly co-located in three-dimensional space of similar extent, and the point clouds must not be too sparse. No feature-detection algorithms are applied during this process; it is a simple nearest-neighbor calculation to the reference point cloud, whether that is a representation of the same part of the outcrop as the comparison point or not. For the purposes of comparison and validation, the terrestrial laser scan data sets were used as the point of reference, this being the most established and directly validated of the two methods (Boehler et al., 2003; Alba and Scaioni, 2007; Buckley et al., 2008b; Reshetyuk, 2009) and generally used as the benchmark case in comparative studies (e.g., Castillo et al., 2012; Favalli et al., 2012; Gómez-Gutiérrez et al., 2014; Nouwakpo et al., 2016).
4.1. Limestone Quarry, North East England
The precisions reported during the post-processing of the GNSS survey data showed that the position data for the surveyed points from this outcrop were precise to centimeter levels relative to each base station position. The TLS and SfM surveys were conducted on different days about two years apart (7 September 2011 and 21 October 2013, respectively). Two different base station locations were used. As a consequence, the two GNSS surveys with internal centimeter precision are of lower absolute accuracy. Typically the base station locations have decimeter accuracies, and hence the reflector and tripod positions that are georeferenced to them also inherit this accuracy. Any misalignment of the two point clouds in their respective GNSS-derived positions is therefore a composite error that consists of: (1) differences in their absolute position and alignment as determined by the quality of the GNSS survey data; and (2) any differences in morphology between the two point clouds due to method-dependent acquisition, internal processing factors, or physical changes such as vegetation and rock falls. Therefore, a fine-refinement of the alignment of the SfM point cloud was conducted in order to correct for the offset to the TLS point cloud due to the difference in absolute positioning of the GNSS surveys. The refinement was conducted using the iterative closest point (ICP) algorithm (Besl and McKay, 1992) by calculating the transformation required to align the SfM point cloud to the TLS point cloud such that the point-to-point distances are minimized. The process assumes that the two point clouds are already closely aligned such that a correct alignment can be converged upon by minimizing the mean of point-to-point distances. The fine-refinement transformation parameters that correct for the offset are shown in Supplemental Table 2 (Supplemental Items, see footnote 1). The fine-refinement process aligned the two point clouds more closely and enabled the point-to-point distance comparison to be implemented in order to investigate differences in the morphology of the point clouds (Fig. 8A). The mean point-to-point distance between the two point clouds was 0.052 m, with a 1σ confidence bound of 0.048 m (Fig. 8B and Table 1). Visualization of point-to-point distances on the SfM point cloud showed mostly consistent point-to-point distances across the outcrop (Fig. 8A). The mean point-to-point distance of 0.052 m is a realistic minimum given the theoretical ground sample distance of 0.004–0.020 for the photogrammetric images and the average point spacing of 0.02–0.03 m for the two data sets. A relative precision ratio of 1:1563 can be estimated, assuming a mean distance from image to outcrop of 75 m (calculated by assuming images at ≈20 m distance affect precision more than those at ≈200 m) and using the standard deviation of point-to-point differences with respect to the TLS data set of 0.048 m as a proxy for local surface standard deviation within the SfM point cloud.
Regions where the point-to-point distances were significantly higher than average are attributed to three factors: (1) Morphological differences between the two point clouds, such as nonlinear distortions that cannot be corrected using a linear transformation applied to the entire outcrop. For example, the ICP alignment converges on the smallest possible overall mean of point-to-point distances, and during this process it accentuated morphological anomalies on east-facing outcrop while minimizing it on all others (Figs. 8A and 8C); (2) reduced fidelity (rounding off of sharp edges) within the SfM point cloud with respect to the TLS point cloud (Figs. 8D and 8E); and (3) variation in limited, localized areas due to additional vegetation growing on the outcrop in the interim period between the TLS and SfM surveys (Fig. 8A).
4.2. Ras al-Khaimah, United Arab Emirates
The SfM and TLS surveys were conducted on the same day (27 April 2015) and shared a common base station position for their GNSS surveys. Post-processing of the GNSS survey data showed that the position data for the SfM tripod positions and TLS reflector positions were accurate to centimeter levels relative to the base station. The use of a shared base station in the SfM and TLS surveys meant that the GNSS-derived alignment of the two data sets was already closely positioned in an absolute sense. Fine-refinement of the alignment of the SfM point cloud was conducted using the ICP method described in Section 4.1. The fine-refinement transformation parameters are shown in Supplemental Table S2 (Supplemental Items, see footnote 1) and describe a set of minor rotations and translations that align the SfM point cloud to the TLS point cloud. Following the fine-refinement, the point-to-point distance comparison was used to investigate differences in the morphology of the point clouds (Fig. 9A). The mean point-to-point distance was 0.074 m with a 1σ confidence bound of 0.052 m (Fig. 9B and Table 1). This is a realistic minimum given the theoretical ground sample distance of 0.017 for the photogrammetric images and the average point spacing of 0.04–0.07 m for the SfM and TLS data sets, respectively. A relative precision ratio of 1:1154 can be estimated assuming a mean distance from image to outcrop of 60 m and using the standard deviation of point-to-point differences with respect to the TLS data set of 0.052 m as a proxy for local surface standard deviation within the SfM point cloud.
Three clear morphological features were revealed in the visualization. (1) Increased point-to-point distances on many of the vertical outcrop faces (Figs. 9A, 9C, and 9D), representing a small lateral offset of the SfM point cloud with respect to its TLS counterpart. This indicates reduced internal consistency within the SfM point cloud because the ICP algorithm cannot eliminate this effect by homogeneous transformation of the outcrop. (2) Increased point-to-point distances at outcrop edges due to reduced fidelity (rounding off of edges) with respect to the TLS point cloud (Figs. 9A and 9E). This is a good example of how SfM data fidelity can degrade significantly if images lack sufficient contrast and perspective change in order to depict the subtle details of the outcrop. (3) Increased point-to-point distances in limited and localized areas due to poorly constrained points located within vegetation growing on the outcrop (Fig. 9A).
The direct comparison of the TLS and SfM data sets presented in Section 4 reveals that both methods are generally suitable for the acquisition of outcrop models but that subtle differences in the performance of the two methods exist. The SfM method produced results that are broadly comparable to TLS for the two outcrops, using similar survey design, distance from the outcrop, and camera equipment. Of the two outcrop examples presented here, the limestone quarry SfM data set is a closer match to its TLS counterpart; however, this is mostly due to a lower mean point spacing in both the TLS and SfM data sets for this outcrop. Both SfM examples honored their TLS counterpart with mean point-to-point distances approaching the mean point spacing for the two data sets (Table 1). Deviation from a consistent match was found to have two distinct causes. Firstly, morphological differences between the point clouds that could not be eliminated using a single homogeneous transformation caused the most distinct mismatch (Figs. 8C, 9C, and 9D). This mismatch suggests that internal inconsistencies exist within the SfM point clouds. These are particularly prevalent when there are restricted perspective differences in the images at the periphery of the survey area due to limited access. Nouwakpo et al. (2016) observed a similar effect with SfM reconstruction of a bare soil surface imaged at ≈2 m range and attributed this to projective compensation of the SfM workflow due to poor image convergence at the periphery of the survey area.
The second main cause of mismatch in the results is reduced fidelity in the finer details of the SfM point cloud with respect to the TLS point cloud. This mismatch produced characteristic rounding off of the sharp edges of the outcrop (Figs. 8D, 8E, and 9E). This rounding off can be attributed to a lack of small-scale image contrast and perspective change between images within these areas sufficient to reconstruct their true small-scale geometric complexity. This effect could probably be at least partially mitigated by acquiring higher-resolution and lower-noise imagery, using sharp (prime) lenses, optimizing camera settings (exposure, focusing, and depth of field), and utilizing image post-processing to improve contrast, reduce lens artifacts (such as chromatic aberration), and to optimize white balance.
It is clear from the two comparisons presented here that performance of the SfM method is inconsistent in relation to TLS, and its success is dependent on a multitude of factors that can vary in their individual significance from one outcrop to the next. Indeed, SfM is not a straightforward technique to implement reliably, and there are many factors that affect acquisition and must be considered carefully in order to yield consistent results. Wide variation in performance of the SfM method in different scenarios is common. Relative precision ratios of SfM data sets when compared to their TLS counterparts provide a means to compare the performance of the SfM method between studies (Table 2). Favalli et al. (2012) acquired TLS and SfM data sets of three outcrops at short range (≈1 m) and compared the SfM reconstruction with respect to the TLS counterparts. Westoby et al. (2012) surveyed a ≈80-m-high coastal cliff at ≈15 m distance and reported SfM differences in relation to TLS in the range of ±0.1 m for low-vegetation areas and ±0.5 m for those that were heavily vegetated. James and Robson (2012) surveyed a 60 × 3 m coastal cliff at 20 m distance and reported differences between SfM and TLS of less than 0.02 m for most of the cliff face. Nouwakpo et al. (2016) reported a difference between TLS and SfM data sets of vegetated plots of 5 mm at 2 m distance. Relative precision ratios for these outcrop studies were in the range of 1:150–2439, which are broadly comparable with results presented here (1:1154–1563). Such variations in precision can make the results of the SfM method difficult to apply consistently in a variety of situations, especially for those geoscientists new to the technique.
Typically, TLS provides a superior and consistently more robust data set when compared with SfM. In a practical sense, the TLS concept of a calibrated time-of-flight device that combines measurements of range and orientation is inherently more robust than the triangulation approach used in SfM. This is not to say that the SfM method is inherently flawed. The main practical drawback of the SfM method is the uncertainty of the internal consistency of the model, in particular an inability to predict the magnitude and extent of non-uniformity (model distortion) within the data. The comparison of TLS time-of-flight measurements to a small number of reflectors whose positions are surveyed using GNSS is sufficient to provide a relatively robust validation of the spatial accuracy of the entire TLS data set (Supplemental Table 1 [Supplemental Items, see footnote 1]). In contrast, within the SfM method, limited subsets of images (those taken from tripod positions) have their position independently validated with respect to comparable GNSS positions (Supplemental Table 2 [Supplemental Items, see footnote 1]). The position of the remaining images and the orientations of the entire image suite are not extrinsically validated, and generally such a limited comparison is insufficiently robust to validate the internal consistency and spatial precision of the entire data set. The crux of the challenge is threefold: (1) Due to real-world practicalities, the ideal image suite required to guarantee consistency and precision can very rarely be consistently acquired in a wide variety of field scenarios (i.e., due to poor outcrop access, lighting conditions, and geometrical outcrop complexity). (2) Previously available off-the-shelf GNSS equipment has not been able to provide sufficiently accurate post-processed positions and orientations for each and every acquired image in an unobtrusive, cost-effective, and time-efficient manner. (3) It is generally impractical to survey ground control points (known markers on the outcrop seen in the point-cloud model) with sufficient density to validate the entire data set, especially when applied to directly inaccessible outcrops.
There are a number of approaches that could be applied to improve the internal consistency of the SfM surveys in this study. These include the use of prime (i.e., single focal length) lenses, fixing the focusing of the camera lens because the camera calibration is known to vary with focusing (Fryer and Brown, 1986), image correction for chromatic aberration (e.g., Remondino and Fraser, 2006), and the use of additional ground control points to try to provide extra constraint and further independent validation of the models. In order to explicitly constrain the positions and orientations of the entire image suite, next-generation GNSS chipsets and 9-axis inertial measurement units (IMUs) appear to have the potential to offer sufficient functionality to provide high-accuracy, post-processed data in a compact and cost-efficient package.
These current limitations further highlight the complexity of proper implementation of the SfM method. SfM does have an important place as a field-based data acquisition method. However, in most situations where data accuracy, consistency, and reliability are paramount (and where there are no means beyond GNSS surveying to validate the results), TLS is generally superior and preferable. In comparison with TLS, to acquire spatially consistent, high-quality data, SfM requires considerably more skill, survey planning, adherence to theoretical principles, and independent validation. In situations where a minimum spatial precision is required across the outcrop, it is insufficient to state that a SfM data set honors a limited number of independently surveyed positions and that on the whole the data “look correct”; in our experience, this approach will typically fail to identify any significant internal inaccuracies within the data. As usual, the key consideration is to ensure that the inherent precision and accuracy of the method are sufficient for the intended application of the data set.
Beyond the direct comparison of the data and its inherent quality, there is a further set of real-world practical considerations that relates to the suitability and implementation of each method in the field. These practical considerations are outlined in detail for each method in Table 3 and relate to the baseline performance of the two methods, their physical properties, cost, operator and processing requirements, general availability, and ease of servicing or part replacement. A comparison of the two methods in this manner provides a basis for selecting the best approach to suit the particular task at hand. Another set of practical considerations of the relative performance and suitability of the two methods in real-world operating conditions is presented in Table 4.
It is clear from this comparison that both methods have their inherent strengths and weaknesses. The ability to be proficient in multiple acquisition methods provides choice for the geoscientist as to which is the most appropriate method to use in particular circumstances. This choice allows for increased flexibility, increased success rates, and improved measurements and interpretations. In many situations, either TLS or SfM can be used successfully to acquire virtual outcrop data or can be combined to produce hybrid data sets (e.g., Bistacchi et al., 2011; Barsanti et al., 2012; Richter et al., 2016), providing the strengths and weaknesses of the methods are considered and the corresponding impact on the planned measurements and interpretations is understood.
Terrestrial laser scanning (TLS) and structure-from-motion (SfM) photogrammetry provide competing and complementary methods of digital outcrop acquisition. Comparisons of the two methods illustrate that in general both are well suited for use in the field. Each method produces broadly comparable results and can be applied successfully in a wide range of situations. The suitability of each method under specific circumstances depends on the purpose of the work, the expected results, the nature of the outcrop, and the prevalent operating conditions.
Real-world considerations in a range of operating conditions highlight the practical strengths and weaknesses of the TLS and SfM methods. SfM equipment is lighter, more compact, cheaper, more easily serviced or replaced, and has lower power requirements. TLS acquisition is more robust (i.e., lower likelihood of inadequate results) in a wider range of operating conditions, is usually extrinsically validated (using GNSS), and data are typically quicker to post-process.
Quantitative comparison of the outcrop models created using both methods indicates that TLS data have higher spatial precision and are more consistent across the outcrop. The fidelity of SfM data is locally reduced due to rounding off (smoothing) of sharp outcrop corners. Spatial precision of SfM data can deteriorate toward the edges of the outcrop, due to poor image convergence toward the periphery of the survey area.
Internal consistency and spatial precision and accuracy are important considerations when using digital outcrop models as the basis for detailed quantitative measurements and analysis, although these considerations are less important when using virtual outcrops as conceptual analogues or for qualitative studies. Studies based on quantitative analysis of virtual outcrops should include better documentation of spatial error.
Fieldwork in the United Arab Emirates was carried out with support from Rutherford International Fellowship Program project no. 15312 funded by Petroleum Institute (Abu Dhabi). We thank Alessandro Fornaciai and an anonymous reviewer for constructive and helpful reviews and Francesco Mazzarini for scientific editing.
↵1Supplemental Items. Supplemental Table 1: Registration errors between terrestrial laser scanning–reflective targets and GNSS-surveyed positions. Supplemental Table 2: Structure-from-motion (SfM) transformation parameters describing the alignment of the SfM point cloud to the real-world GNSS-derived reference frame and the additional fine-refinement to align the SFM dataset with the terrestrial laser scanning dataset. Supplemental Figure: High-resolution versions of Figures 4C (a) and 7C (b). Please visit http://dx.doi.org/10.1130/GES01342.S1 or the full-text article on www.gsapubs.org to view the Supplemental Items.
- Received 12 April 2016.
- Revision received 9 August 2016.
- Accepted 13 September 2016.
- © 2016 Geological Society of America